How do you really feel in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't exactly brain surgery, but it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably hard job. If the old tub is readily accessible, the task can relocate easily; if you need to open up a wall to get rid of the old tub as well as place the brand-new tub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will certainly need an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the work as well as fit attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to think about using one before you start. Possibilities are you might need an expert plumber to make tube links.
This post will certainly assist you mount a brand-new bathtub in your shower room if you have actually currently bought a brand-new tub and do not require to transform the plan of your previous water pipes.
Your devices and also material checklist need to make up the following:
Planning for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to stop stress on the tub.
Fit the flexible faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of getting rid of the existing taps can be quite bothersome due to the restricted gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel all set for the remaining water that will certainly come from the pipelines. When the supply pipelines have been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before moving on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Making use of both wood boards under its feet, position the tub in the needed position. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four small points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the bath tub until the level checks out level.
To mount taps, fit all-time low of the outermost versatile faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Activate the supply of water and check all joints and also brand-new pipework for leakages and tighten them if necessary. Fill up the bathtub and also check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, repair the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub ought to wait until the tub has been made use of a minimum of when as this will settle it right into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washers are in location between the faucet and also the sink. Secure the tap in position with the maker given backnut. As soon as the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former type needs to be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a rigid seal, creating the water to penetrate the wall between the bath as well as the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components as well as installations. They are offered in tubes and cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to allow for the movement experienced when the bathtub is in use. The sealer can split rather early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently available on the market. It is recommended to fit the tiles making use of water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading up on Tools You Need to Install a New Bathtub ? Write a short review down below. We'd be pleased to know your thinking about this entry. We are looking forward to see you back again later on. Do you know about somebody who is excited by the subject? Take a moment to promote it. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Visit My Site